Posted on

How to create a Solar Panel from scratch

Learn how to create a solar panel from scratch is fun and still want some additional skills. This article will provide brief but clearly the DIY guide to create a solar panel from scratch, i.e. things that are irrelevant to her, and does not throw dust bin or what valuable yet now found all use. To prepare to learn something new today by taking a few minutes to read this article.

Required elements:

However, all the necessary elements are found in and around his house and have no pains to buy something new to the solar panel here. The elements listed below;

screwdriver or

or a wooden Saw. (Electronic Sierra wood should be preferred and Saw a hand)

Soldering Stechkin or

Machine for drilling or

copper cables or

Snipping Tool or cutting cables.

or brush.

Electrical welding paste or

or leaf Plexiglas.

or silicon Calc.

Or rosin flux pen.

These were some of the elements should be fully virtual memory elements, which will be used to create the solar panel. Virtual memory elements used are the following:

wooden floor coverings or of great length and width

Tin tubes or

However, there are some items that were purchased in the shop equipment. They are UV varnish protection and span. But even this may be, if you have already used a solar panel.

How To:

or cut the plywood dimensions that can accommodate all of the cells and the paint cut wood with a UV varnish protection.

or a combination of each cell each other via cables and solder them, but before that make sure the apply to all sample bars in cells using flow pen Rosin fluxes.

or attach the plywood using silicon Calafate dabs of these cells.

and remember to accommodate gaps two wires are deducted from the last cell in the solar system. They were fed with the cables through the holes, after critical sealing with silica beads.

or the next step is to drill holes in the plexiglass on screw stays through them.

or build a framework to support Plexiglas.

or use silicon and screws included with plywood frames Plexiglas cells.

a solar panel, or by what is ready. Make sure that the carefully collected all the parts.

Posted on

Make sure that a solar panel from scratch (1)

See how at the beginning of the solar panel is funny, and even have extra skills. In this article, I will give a very short yet clearly the DIY Guide to building a solar panel from the start, that is to say, things should not be used, you can instead generate a dust bin or what a valuable yet found all the outside just now. Yes, you get ready to learn something new today by taking a few minutes to read this article.

Necessary elements:

There are only these things, travel and home and around the do not enable aching to buy something new here, so that the solar panel. Here are the necessary elements required;

screwdriver for

with a wooden Saw. (E-tree must be the primary instead, Saw a hand Saw)

a Soldering gun

Drilling machinery

About Copper rods

a Cutter to cut the wires.

about the painter.

electronic solder pastes

a sheet of plexiglass.

the calculation of PI

about rosin flux of the magnetic pen.

These were some of the use of full items that are used to build a solar panel to the elements that need to be. To disable the elements listed below, which are used to:

of significant length and width of the plywood

Tin pipes

However, certain aspects, which bought the equipment storage. They span and protective varnish. But even this could be allowed if a solar panel has already been used.

How To:

o cut the dimensions of the plywood, which has a capacity of solar cells and paint it for cutting plywood with protective varnish.

to Connect with each other by cables in every cell and solder them, but use it for all the samples of banners in the cells with the use of rosin flux, magnetic flux pen.

about Paste using silicon caulk dabs plywood these cells.

o, the other two cables, which can accommodate up to reduce the last gaps in the Solar Cell. Once the cables are fed through these holes, is extremely important to seal the beads of silica.

the next drill will hold the bolts through the plexiglass.

o provides a framework of support plexiglass.

the use of silicon and screws that attach the links to the plywood frame with plexiglass.

o, Yes to a solar panel is completed. Make sure that you have downloaded all the components thoroughly.